Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
Just how do you actually feel on the subject of How to Install a Bathtub?
Mounting a bathtub isn't specifically rocket science, however it does require solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is easily accessible, the job can relocate easily; if you have to open a wall surface to get rid of the old tub and position the new tub, the task is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the job and fit trying it. Instead of hiring a contractor to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your washroom if you have actually already bought a new bathtub and also do not need to transform the plan of your previous water supply pipelines.
Your tools and material checklist need to consist of the following:
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its final setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any type of water remaining in the system. The process of removing the existing taps can be quite bothersome as a result of the limited access that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will come from the pipelines. When the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the needed placement. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the level and also readjusting the feet on the bath tub till the level reads level.
To install faucets, fit the bottom of the outermost flexible tap adapter to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the water and check all joints as well as new pipework for leakages and tighten them if required. Fill the bathtub and additionally check the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub should wait until the tub has been utilized at least once as this will settle it into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location in between the tap and the sink. Protect the tap in position with the supplier offered backnut. As soon as the faucet is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former type should be linked to the faucet ends first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, creating the water to pass through the wall surface between the bath as well as the tiling, leading to issues with wetness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water before securing, to permit the activity experienced when the bathtub is in usage. The sealer can fracture relatively very early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently available on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very intrigued by How to Install a Bathtub and I really hope you enjoyed reading the new page. Are you aware of anybody else who is interested by the topic? Please feel free to share it. Thank you for your time invested reading it.
Sink issues? Expert consultation here. Report this page